Tel: +86 138-8336-6528  |  cqzymyw@163.com 中文官网  |  English
Menu
Cultural History

What Is a Mortise-and-Tenon Waterwheel? Nongzheng Quanshu and Yingzao Fashi Joinery

ZY
Zhongyu Craftsmanship Team
⚡ Quick Answer

Spring Folk Park Construction: The 10-Year Secret -and-Tenon Joints Spring is th…

What Is a Mortise-and-Tenon Waterwheel? Nongzheng Quanshu and Yingzao Fashi Joinery

A wooden waterwheel that lifts water without a pump is not a decoration. It is a machine with a chain of buckets, a flume, a wheel and a bearing, and every one of those parts decides whether it still turns in year five. The version still standing in Chinese canals was described in Nongzheng Quanshu (Xu Guangqi, 1639), in the seventeenth volume on irrigation, under the name fanche — the chain pump, sometimes translated as the dragon-bone lift.

We build these wheels in Chongqing, where our workshop has cut timber since 1978. What follows is what actually matters when a heritage machine has to work in a public park, a study base or a resort garden.

What a Fanche Waterwheel Actually Does

The fanche is not a scoop wheel. A scoop wheel lifts water in open buckets fixed to the rim, which means it can only lift as high as its diameter allows. The chain pump works differently: a continuous loop of pallets runs inside an inclined trough, and each pallet pushes a slug of water up the trough as the loop turns. The wheel at the bottom supplies the power, the trough sets the lift height, and the two are independent. That is why a 3.2 m wheel can lift water 4 m, and why the same wheel design has been used for drainage as well as irrigation.

For a modern landscape installation this independence is the useful part. A park usually wants a wheel that looks right for the site, and a lift height that serves a rill, a cascade or a demonstration tank. Sizing the wheel to the lift, rather than the other way round, is the first decision we make with a client.

Why the Frame Has No Nails

Chinese timber frames are governed by Yingzao Fashi (Li Jie, 1103), the Song building manual. Its best-known rule is cai fen ba deng — eight material grades — which fixes every member as a multiple of a base module rather than as an absolute dimension. The practical consequence is that a small pavilion and a large one share the same proportions, and a wheel frame built to those proportions can be repaired member by member.

Mortise-and-tenon joints do two things nails cannot. They keep the frame tight as the timber moves with the seasons, because the joint is cut to a tolerance of 1 to 2 mm and closes rather than opens when the wood dries. And they let the frame be taken apart, numbered and reassembled — which is how a wheel ships in crates and how a park replaces one worn spoke without lifting the whole wheel off its bearing.

Specification Comparison

The three sizes below are the ones we quote most often. Dimensions are for the wheel and frame only; the trough, flume and foundation are quoted separately because they depend on the site.

Component Garden wheel 3.2 m Park wheel 4.5 m Landmark wheel 6.0 m
Wheel diameter 3.2 m 4.5 m 6.0 m
Rim segments 16 20 24
Spokes 12 16 20
Axle 180 mm solid hardwood 240 mm solid hardwood 300 mm, twin-bearing
Lift height up to 2.5 m up to 4.0 m up to 5.5 m
Rotation at low flow 6-9 rpm 4-6 rpm 3-4 rpm
Frame timber larch, 100 x 100 mm larch, 120 x 120 mm larch, 150 x 150 mm
Crates for export 2 4 6
Assembly on site 1 day, 2 people 2 days, 3 people 3 days, 4 people

Rotation speed is deliberately low on the larger wheels. A visitor does not read a wheel by its throughput; they read it by whether they can follow one bucket up the trough with their eye. Six to nine turns a minute is fast enough to look alive and slow enough for a child to track.

Installation: Site, Flume and Silt

Most wheels that stop turning were never the victim of bad joinery. They stop because silt collects behind the flume, the wheel starts dragging in the pit, and grit reaches the bearing. Three site decisions prevent that.

First, the pit. The wheel needs clearance below the rim for the water it lifts and for the rubbish it brings with it; we specify 150 mm of working clearance and a silt trap upstream of the flume inlet. Second, the flume, which must be adjustable, because a channel built to a fixed level will be wrong after the first rainy season. Third, the bearing, which should sit above the high-water mark and be greasable from the walkway, not from a ladder.

Foundation details are the client’s engineer’s call, but we send a loading drawing with the crate list: frame dead load, wheel dynamic load at 6 rpm, and the wind case for the site’s exposure. A wheel is a sail when it is empty, and a park on open ground should not discover that after installation.

Maintenance Through the Year

Monthly: clear the silt trap, check that the trough pallets still seat, and look for water sitting on the rim rather than leaving it. Water on the rim usually means a blocked outlet, not a broken joint.

Before winter: drain the trough, grease the bearing, and check the tenon faces on the frame’s lower members for standing water. Timber that stays wet through a freeze will split along the grain, not at the joint.

Year five: replace the pallets. They wear faster than anything else on the machine and they are the cheapest part to change.

FAQ

Does the wheel need a pump to start? No. It needs flow and head. If the site has neither, we quote a recirculating sump with a small electric pump, which is invisible in normal operation and only there to keep the wheel turning on a dry day.

Can it be used for real irrigation? Yes, and the throughput depends on the trough and the lift rather than the wheel diameter. We publish the flow curve with the drawing so a client can see whether the wheel meets a real demand or only a visual one.

How does it ship? Numbered members in sealed crates, with a marking plan and a member list. Nothing on the wheel needs a crane; the largest single piece on a 6 m wheel is a rim segment.

Will it survive a European winter outdoors? With larch, a drained trough and a greasable bearing, yes. The failure mode we see is not cold but standing water.

Ordering

Send us the lift height, the flow you can guarantee in the dry season, and a photograph of the channel or pond. We reply within 24 hours with a drawing, a member list, a crate plan and a delivered price.

Call or WhatsApp +86 138 8336 6528. The wider product range, including landscape wheels for towns and resorts, is here: ancient waterwheel town landmarks from our factory. For the bracket and corbel work that supports pavilion frames of the same grade system, see dougong bracket restoration and custom corbel sets.

Call/WhatsApp: +86 138 8336 6528
Chongqing Zhongyu Wooden Crafts Products Co., Ltd. – timber structures built in Chongqing since 1978

📬 Get Weekly Woodcraft Insights

Join 10,000+ readers learning traditional Chinese joinery, garden design, and cultural heritage. Every Thursday.

ZY

Zhongyu Craftsmanship Team

48 Years of Traditional Chinese Joinery

Chongqing Zhongyu Traditional Joinery Co., Ltd. — a 48-year experienced factory specializing in traditional Chinese woodcraft, garden architecture, and cultural heritage products. OEM/ODM available, global shipping.

Let's Connect & Share Ideas

Whether you're curious about traditional Chinese woodcraft, interested in custom projects, exploring wholesale opportunities, planning cultural collaborations, eager for technical discussions on joinery techniques & wood finishing, or simply want to ask a question — we'd love to hear from you. Every message receives a warm, personal reply from our craftsmanship team.

✅ Thank you! Your message has been sent. We will reply within 24 hours.

🔒 Your information is safe and will never be shared. We reply to every message within 24 hours.

WhatsApp QR

WhatsApp: +86 13883366528

Get a Free Quote
Leave your contact, we'll reply within 24 hours
🔒 Your info is safe · Reply within 24 hours
✅
Submitted!
We received your message, will reply within 24 hours.
🤖

中裕·智木人在线客服

几代老师傅 · 在线咨询