---
title: "A Registrar Crate Checklist for a Touring Oil Press"
date: "2026-11-23T03:19:04+08:00"
modified: "2026-11-23T03:20:21+08:00"
url: "https://www.guwanli.com/blog/touring-oil-press-registrar-crate-checklist/"
markdown_url: "https://www.guwanli.com/blog/touring-oil-press-registrar-crate-checklist.md"
content_type: "blog_en"
description: "Traditional Oil Press: Wood-Beam Design &amp; Craft Guide For decades, the traditional Zhongyu Wood Art, 48 years factory experience. Contact: +86 13883366528."
---

# A Registrar Crate Checklist for a Touring Oil Press

Most touring oil presses are judged by how old they look. The failure usually starts earlier, in a packing list that treats a 180 kg pressure beam like a prop. A beam that cannot be lifted without a forklift, a frame with no sequence marks, and trays that are not food-safe will turn a three-day install into a week of guesswork.

This article is written from the registrar’s side of the table: what to measure, what to mark, and what to reject before the crate leaves the museum. The reference object is a traditional Chinese wedge press, not a decorative copy. Its logic is simple. A heavy beam applies pressure through wedges. The frame carries the load. The trays catch the oil. Every part needs a handling plan.

## The load path is the first specification

On our standard oil press, the main pressure beam is 300 cm x 20 cm x 20 cm and weighs about 180 kg. The two vertical posts are 220 cm x 15 cm x 15 cm, 45 kg each. The sliding frame is 180 cm x 12 cm x 12 cm at 30 kg. Each oil tray is 40 cm x 40 cm x 10 cm and 5 kg.

These numbers matter because they set the minimum crate length and the number of people on the lift. A 300 cm beam needs about 320 cm of internal crate length once padding and blocking are included. Do not order a crate from the beam’s nominal length alone. The beam also needs four blocking points so it cannot roll against the crate wall.

## What Tiangong Kaiwu says about oil

Tiangong Kaiwu, chapter 12, Gao Ye (Fats and Oils), opens with a useful idea. Oil is locked inside the seed and will not flow by itself. It needs water, fire, wood and stone to release it. That is a process statement, not a poem.

Heat prepares the seed. The wedge press supplies pressure. The wooden receiver holds the liquid. A museum display that shows only the press misses two-thirds of the process. A better exhibit pairs the press with a small seed sample, a heating pan and a clear tray, so visitors can see where the oil comes from. The display does not need to run oil every day. It needs to show the sequence.

## Specification table for a touring set

| Component | Standard size | Mass | Handling note | Interpretive role |
| --- | --- | --- | --- | --- |
| Main pressure beam | 300 x 20 x 20 cm | 180 kg | Four-point block; 320 cm crate | Shows where pressure is applied |
| Vertical posts | 220 x 15 x 15 cm | 45 kg each | Two-person lift; protect tenons | Carries the beam load |
| Sliding frame | 180 x 12 x 12 cm | 30 kg | Bundle with wedges in Crate 3 | Guides the press block |
| Oil trays | 40 x 40 x 10 cm | 5 kg each | Food-safe cover; stack separately | Shows the liquid path |
| Wedges and pegs | Project-specific | Small parts | 10 percent spares; labelled bag | Explains dry assembly |

The table is a handling schedule as much as a size chart. A light part with a sharp tenon can do more damage in transit than a heavy beam on a pallet.

![Traditional wooden oil press frame with mortise and tenon joints](https://www.guwanli.com/wp-content/uploads/2026/08/%E5%8F%A4%E6%B3%95%E6%A6%A8%E6%B2%B9%E6%9C%BA%E6%A6%A8%E4%BD%93.webp)The press frame on the factory floor: the beam, posts and sliding block are separate parts, so the crate plan must follow the rebuild order.

## Crate sequence that survives a loading dock

Number crates by install step, not by component type. Crate 1 holds posts and wedges. Crate 2 holds the beam, blocked at four points. Crate 3 holds the sliding frame, trays and small parts. Put a laminated sequence card in Crate 1, not in a document folder that travels separately.

Mark each timber with a removable label on a hidden face. Do not stamp the show face. If the museum will tour the set more than once, use a small brass tag in a recess and record the tag number in the condition report.

Include a lifting plan. The beam is the only piece that should need a pallet jack or a two-person lift. If the museum’s freight elevator is shorter than 320 cm, plan a vertical beam crate or a site assembly from two halves. Decide that before production, not at delivery.

## Dry rebuild and food-contact questions

Traditional presses are dry-fitted. The frame should lock with mortise-and-tenon joints and wedges, not with nails through the show face. For a touring set, the dry fit is an advantage. It can be taken apart and rebuilt without a conservator. It is also a risk. Small wedges disappear in transit. Pack 10 percent spares and label them.

The oil trays are the food-contact surface. Specify food-grade wood and a finish appropriate for the display mode. If the museum will not press oil, keep the trays dry and use seeds in a closed sample jar. Do not run unknown oil through a display press. Residue attracts dust, and every future cleaning becomes a conservation treatment.

For the full component schedule and finish options, see the [antique oil press product page](https://www.guwanli.com/products-en/old-fashioned-oil-press-longevity/). If you are planning a paid demonstration, the earlier note on [a working oil press as a paid experience](https://www.guwanli.com/blog/working-oil-press-paid-experience-heritage-workshop/) covers ticketing, supervision and cleaning.

## Installation and maintenance

Install on a level floor with a moisture barrier. Keep the room between 45 and 60 percent relative humidity. Dust with a dry brush; do not wet the beam. Check wedge tightness monthly and re-mark any part that moves. Keep a 1 m barrier around the press footprint so visitors cannot lean on the wedges.

Our standard lead time is 45 to 60 days. Structural warranty is 5 years, with worldwide on-site installation available. A set can be shipped disassembled, which is the normal mode for a touring exhibition.

## FAQ

### How heavy is a touring oil press?

The standard set is dominated by the 180 kg beam, two 45 kg posts, a 30 kg frame and four 5 kg trays. The crate and blocking add weight, so confirm the total with the freight forwarder.

### Can the press actually make oil?

Yes. For a museum, many sets run dry and use seed samples to explain the process. If you press oil, specify food-grade trays, a cleaning schedule and supervised operation.

### What is the lead time?

About 45 to 60 days for a custom set, depending on drawings and finish. The structural warranty is 5 years.

### How many crates does a set need?

Typically three. The beam crate is the longest and must allow about 320 cm inside. Confirm the elevator and door clearance before packing.

### Can our team install it without a factory crew?

Yes, with the assembly drawings and a two-person lift for the beam. On-site installation is available worldwide if you prefer a factory crew.

**Planning a touring timber exhibit?** Call/WhatsApp: +86 138 8336 6528. Zhongyu Woodcraft – 48 Years Traditional Chinese Woodcraft Factory, Nationwide Installation.

[Request the oil press specification sheet](https://www.guwanli.com/products-en/old-fashioned-oil-press-longevity/)

---

**重庆中裕木制工艺品有限公司（中裕木艺 / 古玩里）**

- 官网：https://www.guwanli.com
- 采购咨询：13883366528（微信同号）
- 1978 年建厂 · 48 年木作传承 · 源头工厂直销 · 全国上门安装
